Author Topic: Video: How to make a simple, high-performance socket for a scope probe  (Read 5395 times)

0 Members and 1 Guest are viewing this topic.

Offline w2aewTopic starter

  • Super Contributor
  • ***
  • Posts: 1780
  • Country: us
  • I usTa cuDnt speL enjinere, noW I aR wuN
    • My YouTube Channel
This video shows a simple method to make a high performance (low inductance) socket to connect your oscilloscope probe to your circuit under test.  It is easily adaptable to different probe sizes/styles and circuit configurations.



YouTube channel: https://www.youtube.com/w2aew
FAE for Tektronix
Technical Coordinator for the ARRL Northern NJ Section
 

Offline robrenz

  • Super Contributor
  • ***
  • Posts: 3035
  • Country: us
  • Real Machinist, Wannabe EE
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #1 on: September 18, 2013, 02:34:53 am »
Very nicely done w2aew, as always :-+

Offline marshallh

  • Supporter
  • ****
  • Posts: 1462
  • Country: us
    • retroactive
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #2 on: September 18, 2013, 03:26:59 am »
A+ sure beats trying to hold the probe on a small via bending over the spring tip just right... while trying to finagle the scope controls with the other hand!
Verilog tips
BGA soldering intro

11:37 <@ktemkin> c4757p: marshall has transcended communications media
11:37 <@ktemkin> He speaks protocols directly.
 

Offline casinada

  • Frequent Contributor
  • **
  • Posts: 599
  • Country: us
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #3 on: September 18, 2013, 04:05:28 am »
Thank you  w2aew as usual your clarity to show and teach subjects is incredible :)

For more information on the subject everybody should watch Bob Pease (RIP) shows.

http://www.ti.com/ww/en/bobpease/

   (around 8:30 into the video )





« Last Edit: September 18, 2013, 06:49:37 am by casinada »
 

Offline BravoV

  • Super Contributor
  • ***
  • Posts: 7549
  • Country: 00
  • +++ ATH1
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #4 on: September 18, 2013, 04:28:51 am »
Excellent video  :-+, thank you Sir !   :clap:

Offline ablacon64

  • Frequent Contributor
  • **
  • Posts: 370
  • Country: br
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #5 on: September 18, 2013, 02:25:28 pm »
Very good! Thank you for the video!
 

Offline bronson

  • Regular Contributor
  • *
  • Posts: 172
  • Country: us
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #6 on: September 23, 2013, 05:49:44 am »
Oh man, I did not realize Bob did videos...  I gotta catch up on that.

For some great discussion on low noise measuring, check out What's All This Ground Noise Stuff Anyhow, p. 88 in this pdf:

 http://www.ti.com/ww/en/bobpease/assets/www-national-com_rap.pdf

Edit: or go right to the original article with the same text but no picture of a probe in a coily socket: http://electronicdesign.com/boards/whats-all-ground-noise-stuff-anyhow
« Last Edit: September 23, 2013, 08:33:58 am by bronson »
 

Offline Galaxyrise

  • Frequent Contributor
  • **
  • Posts: 531
  • Country: us
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #7 on: September 29, 2013, 07:32:16 pm »
Thanks for the video! Inspired by this, I attempted to make some small loop tips for my probe such that the ground "socket" ended in a straight wire that would be a second probe tip, rather than soldering that ground socket to something. I had a lot of trouble with the plastic retaining ridge on my probe snagging the wire loops and deforming, causing the probe to have a loose fit.  So I went for something stiffer, and ended up with a finishing nail.  It was a lot more difficult to work to the correct shape, of course, but it holds that shape as I take it on and off.
I am but an egg
 

Offline w2aewTopic starter

  • Super Contributor
  • ***
  • Posts: 1780
  • Country: us
  • I usTa cuDnt speL enjinere, noW I aR wuN
    • My YouTube Channel
Re: Video: How to make a simple, high-performance socket for a scope probe
« Reply #8 on: September 29, 2013, 09:22:29 pm »
Nice ground spring adapter. I've also used a paper clip for the same thing, as it holds it's shape well after being formed.
YouTube channel: https://www.youtube.com/w2aew
FAE for Tektronix
Technical Coordinator for the ARRL Northern NJ Section
 

Offline madshaman

  • Frequent Contributor
  • **
  • Posts: 698
  • Country: ca
  • ego trans insani
Video: How to make a simple, high-performance socket for a scope probe
« Reply #9 on: October 01, 2013, 04:40:18 pm »

Oh man, I did not realize Bob did videos...  I gotta catch up on that.

Do a youtube search for Bob Peace, you'll be happy.  Gave me many hours of bathtime entertainment (yes, I have a TV at the end of my bath connected to an Apple TV, not bragging, recommending a similar setup, you can read and watch tech videos and take a soak all at the same time, my gf thinks I'm nuts but loves me anyway)
To be responsible, but never to let fear stop the imagination.
 


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf