Low cost iron shootout

[EEVblog]

Is in the planning.
I have some of these already:
FX-888 at US$100
New Weller WE-1010 at US$135
Quick 3104 at US$140
Ersa Pico at US$155 (Amazon price, much more elsewhere, so maybe not a good choice?)

Any others? (maybe one more possible, don't want too many)
Say US$150 tops.

The new Pace one looks nice but it's $250.

[kalel]

What about that famous TS-100?

Of course, low cost is relative, but this one has been recommended on this forum to beginners so frequently, that I would like to see it featured with the "big names" you mentioned.

[EEVblog]

What about that famous TS-100?

Nope, mains stations only.

[Gyro]

That's shame given the availability of suitable laptop bricks. It would have been good to see a decent comparison of thermal performance against the others,  ... but it's your shootout, your rules.

[Muttley Snickers]

Rhino Tools in Sydney currently have a 60 watt soldering station on special for $70 down from $110, it looks similar to the desoldering station you reviewed years back, anyway it might be worth a look.

Rhino Tools.
https://www.rhinotools.com.au

[rea5245]

I get by just fine with the Weller WLC100 for US$40. I set the dial to 3 for most soldering or to 5 when I'm soldering onto a ground fill. I  can do SMT down to 0.5mm pitch. Maybe the WLC100, without a digital temperature display, is beneath contempt ( ) and maybe I'm clueless, but I honestly don't know why I'd need a more expensive iron.

- Bob

[kalel]

I get by just fine with the Weller WLC100 for US$40. I set the dial to 3 for most soldering or to 5 when I'm soldering onto a ground fill. I  can do SMT down to 0.5mm pitch. Maybe the WLC100, without a digital temperature display, is beneath contempt ( ) and maybe I'm clueless, but I honestly don't know why I'd need a more expensive iron.

- Bob

Good quality solder probably makes a bigger difference than the iron, but if all else is equal, some might be handier than others (beside temp control and display stuff, different handle shape, etc) - but that still doesn't have to mean you'll prefer a more expensive one (I never tried one with any kind of real price to it).

In fact, this shootout might show us some reasons why one can be better than another.

[cdev]

I'm pleased with the FX-888D so far. No need to keep riding the temp settings like I had to before. Which is nice. And it came with a basic chisel tip, not a conical which is also good because its my most often used tip.

I actually got the Fx-888D for $89 with free shipping from a big West Coast chain.

For that I really couldn't say no.  Going to spend some quality time melting solder later today, I hope.

[wraper]

What about that famous TS-100?

Nope, mains stations only.

Why wouldn't it fall under "mains station" description? It just requires PSU to be bought separately. It has the same power rating as FX-888D

[lem_ix]

The Ersa Pico costs about 165 euro here, cheapest Weller being the WHS40 ~ 125 euro and about 140 for the digital one. No Hakko distributor here so those are the cheapest big brand stations you can get. Only suggestion that comes to mind but is hard to find is Jovy iSolder 40. It's been mentioned around the forum a few times. I've seen a price of 120 euro or so.

http://www.jovy-systems.com/en/products/solder-stations/isolder-40.html

[asmi]

I use cheap-ass 852D+ combined iron+hot air gun station for over 2 years now with both leaded and lead-free solder. It's not just iron, but it's about $60 for the whole thing, so it fits the bill price-wise.

[Dan Moos]

A ton of of us use the Weller WES51. I for one would love to see it included so that I might see a direct comparison to those other irons do that I might know what, if anything, I'm missing out on.

Sent from my E6830 using Tapatalk

[lmaokore]

A ton of of us use the Weller WES51. I for one would love to see it included so that I might see a direct comparison to those other irons do that I might know what, if anything, I'm missing out on.

Sent from my E6830 using Tapatalk

The Weller WES51 is being phased out and being replaced by the WE-1010. The new Weller has much more power.

[bd139]

Quicko T12 on aliexpress. Quite frankly shits on my weller.

[Dan Moos]

If Dave included the old Weller, the direct comparison with the new (and the others) would help me and other owners decide whether it's worth upgrading.

Sent from my E6830 using Tapatalk

[asmi]

If Dave included the old Weller, the direct comparison with the new (and the others) would help me and other owners decide whether it's worth upgrading.

What's the point of upgrading? It's an iron. Either it works, or it doesn't. Higher power means the iron will heat up a bit faster. Like 2 seconds faster. Is it worth fretting over?

[wraper]

If Dave included the old Weller, the direct comparison with the new (and the others) would help me and other owners decide whether it's worth upgrading.

What's the point of upgrading? It's an iron. Either it works, or it doesn't. Higher power means the iron will heat up a bit faster. Like 2 seconds faster. Is it worth fretting over?

Power as such does not mean that much by itself alone, and higher power does not mean faster heat-up time. 2 irons may have same power but performance different like day and night, and 10 times different heat up time.

It's an iron. Either it works, or it doesn't.

[xygor]

I would love to see how these two fare in the lineup:
Edsyn 951SXE Soldering Station with Analog Display (US $145)
Aoyue 2930 Programmable Digital Soldering Station (US $72)

[Dan Moos]

I would love to see how these two fare in the lineup:
Edsyn 951SXE Soldering Station with Analog Display
Aoyue 2930 Programmable Digital Soldering Station

Wraper, anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

I have an iron (WES51) that I am mostly happy with. That said I was mostly happy with it's preticesor, a 60 watt pencil iron from radio shack. I didn't realize what I was missing until I got the Weller. The RatShack iron "worked", so by your assessment, a desire to see it compared to something similar but better would be pointless. It clearly isn't.

Dave can do whatever he wants, but i'd love to see an iron that half the hobbiest here possess compared to the current crop of similarly priced tools. It would help me know if the grass is greener on the other side, or not.

Sent from my E6830 using Tapatalk

[Dan Moos]

I would love to see how these two fare in the lineup:
Edsyn 951SXE Soldering Station with Analog Display
Aoyue 2930 Programmable Digital Soldering Station

Wraper, anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

I have an iron (WES51) that I am mostly happy with. That said I was mostly happy with it's preticesor, a 60 watt pencil iron from radio shack. I didn't realize what I was missing until I got the Weller. The RatShack iron "worked", so by your assessment, a desire to see it compared to something similar but better would be pointless. It clearly isn't.

Dave can do whatever he wants, but i'd love to see an iron that half the hobbiest here possess compared to the current crop of similarly priced tools. It would help me know if the grass is greener on the other side, or not.

Sent from my E6830 using Tapatalk

Sorry for quoting the wrong post here. Tapatalk on  my phone is not one of my better skills!

Sent from my E6830 using Tapatalk

[wraper]

Wraper, anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

Didn't you mean asmi?

[Dan Moos]

Wraper, anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

Didn't you mean asmi?

Oops. Yup. Sorry!

Sent from my E6830 using Tapatalk

[David Hess]

A ton of of us use the Weller WES51. I for one would love to see it included so that I might see a direct comparison to those other irons do that I might know what, if anything, I'm missing out on.

The Weller WES51 is being phased out and being replaced by the WE-1010. The new Weller has much more power.

I was going to say the same thing about including the WES51/WESD51 but if the WE1010 is replacing them, then that answers that.

Wraper, anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

I have an iron (WES51) that I am mostly happy with. That said I was mostly happy with it's preticesor, a 60 watt pencil iron from radio shack. I didn't realize what I was missing until I got the Weller. The RatShack iron "worked", so by your assessment, a desire to see it compared to something similar but better would be pointless. It clearly isn't.

There is a huge difference between a non-temperature controlled iron and a temperature controlled iron.  But the difference between a 50 watt WES51/WESD51 and 70 watt WE-1010 is going to require a fine test to discern if they use the same tips which appears to be the case.

[asmi]

anyone who has done any amount of soldiering knows "either it works it it doesn't" is a gross simplification. If that were the case, what's the point of the shootout, and thus why would you even care to comment?

How is it so? If your existing iron works for you, what's the point to change it?

[sreeb]

If you have access to amazon and want cheap then this:

https://smile.amazon.com/Weberdisplays-Soldering-Sigma-850-Calibration/dp/B01DSB2A96/ref=cm_wl_huc_item

Updated:  This has digital control, uses Hakko T12 cartridges, and costs US $25 with amazon prime delivery.