F/S Lecroy,Tektronix scopes,Advantest SA,R&S SA,Bruel&Kjaer mic.Huge price drop!

[smaultre]

Advantest 8GHz U3751 1600$ + Shipping

Advantest 8GHz U3751 with TG 2100$ + Shipping

Lecroy WS424 500$ + Shipping
 
Lecroy WS3054  +Gen+ Serial Decode+ Logic analyser 2200$ + Shipping

Lecroy WS64MXs 1500$ ! + Shipping

Lecroy WR44Xi upg WR64MXi    1600$ + Shipping

Lecroy WR104Xi  2300$ + Shipping

Lecroy WP7200A XL 1850$ + Shipping

Lecroy WP960 XXL  1499$ + Shipping

Lecroy WR610zi XXL 3800$ + Shipping

Tektronix AWG5002B 3100$ + Shipping

Tektronix VM5000HD 899$ + Shipping

Fluke 199C + Bushealth mod 600$

Fluke 199C X-Ray(medical) 200MHz 2Gs/s 800$  + Shipping
Fluke 199C X-Ray(medical) 200MHz 2Gs/s + case+ full set 1200$  + Shipping
 
Tektronix TDS3012B >>(3064b) 600MHz 280$ + Shipping

Anritsu S331E (no batt cover) + bag 1000$ + Shipping

Anritsu S332D   /Options: /3 /29 int. power meter spectrum e.t.c  / +2batt+ PSU + bag 900$ + Shipping
      
R&S   FSH3+TG   + options 950$ + Shipping

R&S   FSH3+TG+PA +options 1000$ + Shipping

R&S   FSH6 +PA (no display plastic cover )+PA +options 1100$ + Shipping

R&S   FSH18 +options 4400$ + Shipping


Also i have some more Bruel&Kjaer, GRAS devices, mics, ears, sensors, calibrators, front-ends, including unobtanium ultra-rare..

All equipment can be checked during a video-call session. Or meeting in person.

There's ton's of tested equip in my profile https://www.ebay.com/usr/sukho_641

CA, DTLA.

[vinovino]

Is the item below still available:
Tektronix TDS3000(B) TDS3GV   VGA RS232 GPIB module

[smaultre]

Hello, this- one sold..

[smaultre]

Lecroy's added.

[joeqsmith]

Depending on condition, that's a good price on the Lecroy WR64Xi 1900$ + Shipping.   I bought one recently for parts to repair mine or I would be interested. 

[smaultre]

https://www.ebay.com/itm/355924957402

For repairs you can buy WS64 internally them identical.

[joeqsmith]

Mechanically, it looks like about as good of condition as mine.  Maybe better.    I'm not a fan of these plastic parts. 

You may want to consider providing the SN# allowing potential buyers to contact LeCroy to get the service history.  Early versions seemed to have a high failure rate.  When looking for a junker, one prerequisite was the second generation hardware.   

[smaultre]

I have not observed such a pattern based on my experience
~40 devices

[joeqsmith]

I have not observed such a pattern based on my experience
~40 devices

I posted about mine and member Wuerstchenhund explained how it was a common failure with the early ones.  Try using the search if interested.  The scope I bought for parts was an early SN.  LeCroy pulled the service records for it and indeed, it also had failed the same as mine.  In this case, they had replaced the hardware.   

I've not had any troubles after my repairs.  Installed a new battery while I was in there.  But, its only been a few months.   Back in 2015 when Wuerstchenhund, one concern he had was my my use of an SSD, claiming he was seeing failures in a short time.   It's now close to 10 years of service with the SSD without a problem.  Their use of plastic and a poorly designed case has been the big problem.  At least they solved the knobs falling off as the second generation ones they provided remain tight (all of mine are now replaced).   
 
From the LeCroy groups.io:

While testing a 64Xi I just got, I saw a behaviour I’d not seen until now…
channels 1,2 and 4 are OK, but 3 seems dead.
it displays some sort of sawtooth pattern, with an amplitude of ~1/3 of a div, whatever the scale, input signal is ignored, and vertical offset doesn’t apply, you can set whatever offset you like, the trace always jumps back to level 0, the offset marker is at the right place, but the actual trace is always displayed as if the offset was 0

Does this ring a bell somewhere ?? Any ideas/hints ?
(I don’t see any errors in the logs, so far)

[smaultre]

Some new old  equip arrives!

[smaultre]

New equipment arrived! More price drop!