-
ESD Mat
Posted by
requim
on 09 Nov, 2011 19:41
-
I'm looking to buy a high quality 2 or 3 layer rubber ESD mat similar to what Dave has in his lab. I've priced some out and found that they are indeed quite pricey. I'm not sure whether there is a big difference between the various vendors. Anyway it occurred to me that if I could find others to split the cost with that buying a roll and splitting it up would save each of us a significant amount of money. Rolls are typically in the 40-50 foot range. I'd like something in the neighborhood of 5 feet x 3 feet or 60 inches by 36 inches. By that standard I would need to find 7 - 9 other people who would be interested in participating.
I'm in the US so to make it easier on myself I'd rather only do this with others in the US. I think shipping would make it prohibitively expensive for anyone outside of the US.
The general price I'm seeing for a 3x5 foot mat is $100+ whereas a 50 foot roll is around $500. I've seen them a bit cheaper and I've seen them for over a grand. I'm open to suggestions since it's all greek to me.
Is there enough interest to do this? or should I just bite the bullet and spend the big bucks for a single mat? If anyone is interested either leave a message here or shoot me an email titled "EEVBlog ESD Mat".
-
#1 Reply
Posted by
IanB
on 09 Nov, 2011 21:46
-
Are you looking to buy a gold-plated mat? I've looked around and it seems you can buy static dissipative desktop rubber work mats in the US at prices from $15 up. For home use I think I would be happy myself with one of those. Given the inevitable damage from flux spills, cuts and solder drips I'd rather have something disposable than something expensive.
-
#2 Reply
Posted by
requim
on 09 Nov, 2011 22:11
-
-
#3 Reply
Posted by
IanB
on 09 Nov, 2011 22:19
-
-
#4 Reply
Posted by
requim
on 09 Nov, 2011 22:28
-
What's the difference? If we're talking need I could get by without a mat altogether and risk it. I'd like to buy a mat that will last for a long time. I have no experience with the cheap ones or the expensive ones. The inexpensive ones are usually small and I assume have a relatively short life span. I'd like one to cover my table/workspace that will last for decades (if that's even reasonable). If I buy a larger one then I'll have plenty of space to do my computer builds as well as my electronics stuff.
Need/want, it's all the same. I'm willing to spend the money to get what I want. I figure if others are interested in doing the same then I may was well see if we can do it at a lower cost. If not, then I just need to decide which one I like best and make the jump.
I'm certainly open to suggestions. Oh and for the record I've seen the one on Amazon you linked to as well as one that's about 80 quid for a computer builders mat. The computer builders mat looked decent, but I didn't have much faith it would stand up to solder very well. From what I understand rubber is the best option for soldering.
-
#5 Reply
Posted by
IanB
on 09 Nov, 2011 22:40
-
I don't have a mat, but I think the ones on Amazon are mainly intended for computer dis-assembly rather than soldering. But they can still come in a decent size such as 2' x 3'.
The expensive ones you linked to are heat resistant and mechanically stronger, and that is perhaps why they cost more.
On my workbench at home I have a sheet of corrugated cardboard to protect the surface underneath. It means I can treat it like a work surface and not have to care about damage, and I don't have much concern for static with what I use it for. If I wanted an anti-static mat I would get one of those ones from Amazon to see what I liked and didn't like about the design before I spent more money on an expensive one.
-
#6 Reply
Posted by
requim
on 09 Nov, 2011 22:49
-
I'm just not sure buying a $16 vinyl mat on amazon is really going to tell me anything. I'd also need to buy a 2 layer rubber mat as well and a small one of those is still going to run around 40 - 50 for comparison purposes. From what I've read rubber is the way to go. If I'm not mistaken it's what Dave uses. I'd love to know exactly which mat he uses so I can at least use that as a point of comparison in my decision making process.
@eevblog -- how about it? Can you tell us what mat you use?
I figure at the end of the day if I buy one it will run me about $100. I view it as an investment, because heaven knows i've been building computers for decades without one. I figure since I'm getting more into the component side of things I should play it safe and get an ESD mat.
-
-
try using the search above it could just reveal answers like
https://www.eevblog.com/forum/index.php?topic=5339.0 without waiting for personal assistance.
Most people here do try to help when possible, but they can be busy (or watching BTTF reruns at the time) and will appreciate any efforts you can make to help yourself. The is a huge compendium of knowledge setting here in existing threads.
-
#8 Reply
Posted by
Balaur
on 10 Nov, 2011 00:01
-
Yes, those look nice, but do you really need one like that, when one like this might do? http://www.amazon.com/gp/product/B000TAAHJA
I have exactly the same one at home. Perfectly adequate for home use. The only drawback (beside that's too cheap
is that it's not heat resistant.
One drop of molten solder and it's worse that Aliens' blood. You should also keep the hot air from it as well.
But I can perfectly live with this limitation since I usually have good solder discipline.
At work we have much better ones that have seen a lot of abuse. They are not invincible though.
Cheers,
Dan
-
#9 Reply
Posted by
requim
on 10 Nov, 2011 00:18
-
@Uncle Vernon - you assume I didn't read the thread prior to posting. If you notice I posted this under Buy/Sell/Wanted, not General Chat. I still have yet to see Dave state which specific mat he uses, hence the question. However my original proposal holds true, to see whether anyone wants to go in on splitting a roll to reduce the unit cost or whether I'm just going to buy one.
If you have any links that show discussions/reviews of various ESD mats I'd love to see them because I have yet to find them in my searching.
-
#10 Reply
Posted by
requim
on 10 Nov, 2011 00:21
-
@Balaur - at this point I couldn't tell you what constitutes good solder discipline versus what doesn't. I don't routinely find solder on my table nor do I leave the iron on the table. I do however find that my table gets torn up with the various electronic components, disassembled units, etc that get pushed, pulled, turned, etc on the table top. I do not know how any of the mats will hold up under those conditions.
-
#11 Reply
Posted by
IanB
on 10 Nov, 2011 00:33
-
I do however find that my table gets torn up with the various electronic components, disassembled units, etc that get pushed, pulled, turned, etc on the table top. I do not know how any of the mats will hold up under those conditions.
I don't think you will want to cover your entire work surface with a work mat, just a small area in front of you where you do assembly and soldering. Even the most durable mat will not survive being used as an every day work surface.
As for what Dave has, it has been posted here somewhere. It is some of that expensive kind of stuff you have been looking at, only from an Australian supplier.
I would not be that interested in a group buy since the quality stuff is about $1000 for a 50' roll and by the time it is cut into individual lengths and then shipping costs are taken into account there does not seem to be much of a cost saving.
-
-
@Uncle Vernon - you assume I didn't read the thread prior to posting.
You have no basis for knowing what the feckz I am assuming or not assuming.
If you notice I posted this under Buy/Sell/Wanted, not General Chat.
What has that got to do with the price of nougat in Norway? Were you assuming that somehow has special status?
I still have yet to see Dave state which specific mat he uses, hence the question.
It's not my OR YOUR business to state what Dave or anyother poster for that matter does or doesn't do. It's a public forum not your little spot for demanding personal assistance from anyone!
However my original proposal holds true, to see whether anyone wants to go in on splitting a roll to reduce the unit cost or whether I'm just going to buy one.
Perhaps someone will be interested.
If you have any links that show discussions/reviews of various ESD mats I'd love to see them because I have yet to find them in my searching.
I just posted you one, I'm sure you can find more if you make the effort. It's an antistatic mat FFS and you want a scrap for a hobby bench what are you expecting molecular analysis. Are you then planning import from the antipodes?
The post quoted included information on the material, pricing and address of some (Australian) suppliers. What were you hoping for? A video of some being shot over a waterfall?
I offered some polite assistance and this is your reaction? I and and a lot of people watching your tantrum will probably not be bothering to assist you further on this one. Enjoy!
-
#13 Reply
Posted by
requim
on 10 Nov, 2011 00:51
-
Wow I didn't realize I was the one having a tantrum. I stand corrected. I'm just here looking for help and trying to learn.
-
#14 Reply
Posted by
requim
on 10 Nov, 2011 00:58
-
@IanB - I think your analysis is correct. I basically came to the same conclusion, that while I may save ten to twenty bucks it just isn't worth the hassle. C'est la vie. It was worth considering. I'm not excited to spend alot of money on an esd mat.
And perhaps you are right, maybe I need to scale down the size of mat I am looking for. If I keep my equipment on the same table there is no point in having the equipment on an esd mat, but if I put my equipment on a shelf just above the table, then having a large mat would be nice. As it is with computers having a larger mat would be nice to put down the various components without worrying about anything. As for solder work with small pcb's then a small mat seems just fine. Doing repair work seems equivalent to doing computer work so I'd think I'd want a bigger mat.
So it seems in some ways that having two tables / benches is the better option, one to beat up and the other to do soldering, esd type stuff. And for the space constrained, a single bench with a removable esd mat.
-
#15 Reply
Posted by
IanB
on 10 Nov, 2011 01:04
-
I have a moderate sized desk/bench. I have my work mat as a small clear island in front of my chair and the rest of the worktop free for tools, equipment and other stuff I need close to hand. I prefer to have things like my soldering iron off the mat and on the bench top.
-
#16 Reply
Posted by
requim
on 10 Nov, 2011 01:14
-
My work area at the moment is a 3'x5' table that shares space with a couple monitors, keyboard and stereo receiver. Needless to say it's crowded. I put the equipment on the table I need at the moment I'm working on something. This is of course just a temporary issue since I'm in temporary housing. Once I relocated the table will be my entire workbench.
As for whether I'll be able to mount any shelving to place equipment onto is yet to be seen, but the table will not alter in size hence the desire for a 36" x 60" esd mat. I thought the surface would look funny if I had a 24" x 60" mat at the front with the last foot showing the surface of the table. I still like the idea of having a 60" wide mat and something at least 20-24 inches in depth since I do a lot of computer stuff and building computers takes a fair amount of surface area.
-
#17 Reply
Posted by
DrGeoff
on 10 Nov, 2011 01:52
-
-
#18 Reply
Posted by
requim
on 10 Nov, 2011 01:57
-
@DrGeoff - Thanks. If only they sold it here in the US. I'll see if I can find a datasheet on it and use that to compare to the ones available here in the US.
-
#19 Reply
Posted by
DrGeoff
on 10 Nov, 2011 02:01
-
I think it is a ChemTools product, distributed here by Okay. You should be able to find ChemTools in the US.
-
#20 Reply
Posted by
Joshua
on 10 Nov, 2011 04:54
-
I would check out All-Spec Industries line of rubber mats. I would not get vinyl. I really like the company - very professional and helpful. I believe I have the Sierra brand heavy duty rubber mat. I have a 2' x 5' mat and it came to about $103 with shipping and mat cleaner. Fast FedEx shipping. Like I said, I really like the service from them.
They also sell rolls of it. Occasionally they have sales in their mats.
-
#21 Reply
Posted by
requim
on 10 Nov, 2011 05:16
-
@Joshua - Thanks for the recommendation. I went ahead and ordered the following:
https://www.all-spec.com/products/APW120G.htmlTotal cost shipped was ~$94. I settled on 24"x60" because I figured that if I got 30"x60" I would have six inches at the back and that everything I put down would end up being off balance. This way anything in the last foot will be level and if anything is longer than that I'll deal with it. If I could have found a 36"x60" I would have bought it. Oh well. Hopefully this lasts me a long time. I'd have preferred dark blue but the option wasn't available.
-
#22 Reply
Posted by
sata
on 11 Dec, 2013 17:33
-
Just want to report another opinion.
Bought the ESD bench matting with extra cushion layer from
http://www.somersetsolders.com/product.php/1068/88/esd_bench_matting_with_extra_cushion_layerIt's cheap and made of rubber, and comfortable to use.
However, as it came it brought a huge smell of rubber, making it almost impossible to be in the same room as the mat. Quite disturbing.
Had tried several methods found on google to remove the smell, but no products helped.
After 20-30 cycles on a hoven at 80 degrees, the smell is now completely bearable.
I'm happy now with my purchase. But had to warn yo guys about the strong rubbery smell.
-
-
-
#24 Reply
Posted by
eKretz
on 22 Dec, 2013 08:45
-